#Piranha cnc touch plate wiring driver
#Piranha cnc touch plate wiring software
#Piranha cnc touch plate wiring plus

Limit switch is damaged (limit switch is always closed), you can change it.Дў. The Twenty-second Problem: CNC router can be reset to X axis, Y axis, Z axis position uncertain.ДЎ. Loosen the drive wire and try to hold it tight. Limit switch failure, the system back to the system origin limit switch has closed and bounce, change the limit switch.Дў. The Twenty-first Problem: When setting the original point of the CNC router, sometimes it moves forward and right, and the distance is not fixed.ДЎ. Check the middle line is connected, whether the thread off the weld.

#Piranha cnc touch plate wiring plus

Working voltage instability or overload, plus a regulator can be.Дў. The Twentieth Problem: During the work of CNC router, the spindle motor stopped suddenly or turned slowly.ДЎ. Check X, Y axis screw and screw is loose. Re-install the new system and software.Дў.

#Piranha cnc touch plate wiring software

The Nineteenth Problem: CNC router software can not be opened normally, carved things deformity.ДЎ. Software parameters set in the software limit. Check the carving path is beyond the scope of sculpture.Дў. The Eighteenth Problem: CNC router in the process of limiting the phenomenon.ДЎ. Drive problem or computer output signal line poor contact. The Seventeenth Problem: CNC router open the software boot, the shaft appears closed.ДЎ. The Sixteenth Problem: CNC router spindle motor does not turn or reverse.ДЎ. Check the Z-axis stepper motor line is bad or in the case of intermittent contact. Check the Z-axis stepper motor is operating normally, the size of the power and drive current or their own failure.Дў. The Fifteenth Problem: When the X axis moves to somewhere, Z axis does not lift the knife, put button to go up but go down.ДЎ. Check that the software parameters are set correctly. Check the size of the gap between the screw rod and light rod fastening screws are not loose.ДЈ. Check the engraving software path is correct or not.Дў. The Fourteenth Problem: CNC router routing misplaced or wrong size.ДЎ. Check whether the 85V power supply is normal. Check the fuse box in the control box adapter plate is burned, for the fuse.ДЈ. Check the computer and the two data lines are not connected.Дў. The Thirteenth Problem: CNC router prompts when opening the software: three axis alarm, initialization error number four.ДЎ. The two data cables to re-install, check there is no broken needle phenomenon.

#Piranha cnc touch plate wiring driver

Check the card driver is not installed, or the board for a PCI slot.Дў. The Twelfth Problem: When the CNC router opens Weihong software, the computer prompts 'operation failed'.ДЎ. The Eleventh Problem: CNC router spindle automatically turn or stop. The Tenth Problem: CNC router can not move back to the origin normally. Modify the motor direction in Weihong software. The Ninth Problem: CNC router moving back or back to the original direction of the opposite direction.ДЈ. The spindle itself has a problem (bearing damage). The Eighth Problem: The working sound of CNC router spindle is abnormal.ДЈ. Inverter parameter setting error or failure.ДҐ. The Seventh Problem: CNC router spindle stop.ДЈ. There is a problem with the control card. Spindle and table is not vertical to be corrected (performance symptoms: under the knife and the knife at different shades).ДЈ. The Sixth Problem: CNC router uneven milling.ДЎ. The computer has a virus or system problem. Drive fault or current subdivision set incorrectly.ДЁ. The Fifth Problem: CNC router carving irregularly.Д¦. Inverter interference or data setting is wrong.

Drive failure or current subdivision and software settings are inconsistent.Д¦.

The Fourth Problem: CNC router carving different shades.ДЈ.

(system parameters curve acceleration is too large) Z axis drive current is too small, or the signal line is wrong.Д©. Z axis motor power is not enough, the coupling loose.ДЁ.

Computer system has a problem or virus.Д§. The Second Problem: Z axis of CNC router out of control (norte knives).Д¦. Drive subdivision, current, and software settings are not the same. The corresponding axis slip fast failure.Д§. The corresponding screw break or screw nut failure.Д¦. The corresponding coupling rupture or loose (coupling loose performance symptoms, engraving fonts dislocation).ДҐ. The corresponding axis stepper motor fault.Д¤. The First Problem: One axis or Three axis of CNC router not moving or moving irregularly.Дў.

CNC Router Parts, Bits, Tools, Accessories.